| Q: |
How
does Strike Sensor work? |
| A: |
Strike
Sensor is a wireless remote strike alert system. It consists of a
receiver (pager) and any number of transmitters. Set up in a variety
of ways for different fishing methods, the transmitter is triggered
when a fish strikes. Silent radio waves are transmitted which beeps
the pager you are carrying with you.
|
| Q: |
What
is the range of the Strike Sensor system? |
| A: |
Because
Strike Sensor works on radio waves it is governed by the FCC and Industry
Canada rules. Strike Sensor is designed to provide the maximum possible
operating distance while complying with governing regulations.
Our newest models (introduced in the Fall of 2001) have been tested
to operate at distances of over 500 feet. Reception distances will
vary depending upon many factors including atmospheric conditions
and precipitation.
For optimal range, the area between the pager and the transmitters
should be unobstructed and in a direct line of sight. The pager antenna
wire should be kept straight up. Carry the pager outside your clothing
in a chest pocket or as high as possible. The higher the pager is
elevated from the transmitters, the better the reception. When fishing
from a metal shanty or lake cottage, place the pager in a window facing
the transmitters.
View Certifications:
FCC Certification
IC Certification
|
| Q: |
So
what do I need? |
| A: |
The
initial package we offer is a receiver and one transmitter (Pager
and Transmitter package). Then you will want to get additional transmitters
to monitor more lines; one transmitter per line. You only need one
pager to monitor any number of transmitters.
|
| Q: |
How
many transmitters can I use with my pager? |
| A: |
As
many as you want. Just be sure to set the DIP switch (located in the
battery compartments) patterns exactly the same in all your units.
|
| Q: |
Will
my transmitters trigger my buddys pager or vice-versa? |
| A: |
No,
not if the DIP switch patterns are set differently. Just use a unique
pattern and there should be no problem. There are 134,217,728 possible
combinations.
|
| Q: |
Can
I use more than one pager? |
| A: |
Not recommended. If you have more than one pager within a few feet of each other, they can interfere with each other as they will compete for the same signal and the range may suffer.
|
| Q: |
Can
this system be used at night? |
| A: |
Yes.
Each transmitter is equipped with an indicator light which illuminates
when the unit is tripped.
|
| Q: |
When
I am fishing with several transmitters, and my pager beeps, how do
I know which one is tripped? |
| A: |
You
cannot differentiate which unit is tripped by the pager. You must
visually check your lines during the day or look for the indicator
light at night.
|
| Q: |
Does
the transmitter emit any sound when tripped? |
| A: |
No,
the transmitter is completely silent. The only sound comes from the
receiver (pager). So there is no chance of disturbing other fishermen
nearby.
|
| Q: |
Can
I use Strike Sensor with any kind of tip-up? |
| A: |
Most
that we are aware of. The transmitter is activated when a metal tab
is removed from a slot. So any tip-up that uses a spring-up or pop-up
flag would be able to lift the metal tab.
|
| Q: |
How
can I get the Velcro to stay on my tip-ups? |
| A: |
Do not
apply the Velcro in the cold. Affix the Velcro when both the Velcro
and the surface in which it is to be applied, are at room temperature
or warmer.
|
| Q: |
What
is the best way to use Strike Sensor for bank fishing? |
| A: |
We offer
an accessory to Strike Sensor called Line Minder. Line Minder can
be attached to any rod holder or bank stick. It provides a holder
for your transmitter and offers completely adjustable trip tension.
Using Strike Sensor in concert with Line Minder is a most effective
bank fishing method. You can also refer to our Bank
Fishing page for more information and photos of different set-ups.
|
| Q: |
What
kind of batteries do the units use? |
| A: |
Both
the transmitter and receiver (pager), operate with one 9 volt battery
each.
|
| Q: |
What
kind (brand) of battery works the best? |
| A: |
Batteries
are very important. Any quality 9 volt will work, however it is necessary
to use either alkaline or lithium batteries. These batteries hold
up best in cold weather and offer optimal performance. Alkaline batteries
are less expensive than lithium batteries, however lithium batteries
are rated for colder weather and longer battery life. Our tests indicate
lithium batteries last more than 2 to 3 times longer than alkaline
batteries.
See the "Battery Life Expectancy Chart"
|
| Q: |
How
should I care for my Strike Sensor units? |
| A: |
As with
any finely tuned electronic devices, these units must be handled with
care. Avoid dropping, jarring or rough handling. Keep your Strike
Sensors in a protective case or box. We offer a canvas carrying case
that can accommodate up to four units. Avoid condensation! After each
outing, bring your units indoors and completely dry them off and store
them in a dry area. During the off season, remove the batteries from
the units before storing for periods longer than 1 month.
|
| Q: |
Are
the Strike Sensor units water-proof? |
| A: |
The
transmitters are designed to be weather-proof. They can be used in
rain and snow without damage. However, do not allow the transmitter
to become submerged in water. They are not water-tight. If a unit,
either a pager or transmitter is dropped in water, DO NOT attempt
to operate until the unit has been completely dried inside and out.
Water on a PC board can short out the circuit and cause permanent
damage.
|
| Q: |
Can
the pager be powered with an AC or DC adaptor? |
| A: |
Yes,
such adaptors can be purchased in the electronics departments of most
larger stores. Adaptors with an output of 9V DC 500mA are recommended.
The AC or DC adaptor plugs into the jack on the side of the pager
and will override an installed battery.
|
| |
Email
us with any questions that are not covered here. |